This is the latest REV-8 G540 drive The G540 is our most popular end-user focused product. Capable of driving four independent motors with its discrete internal motor controls at up to 50VDC and 3.5A per axis, it can move motors ranging from...

This is a Geckodrive G540 REV-8 plus a Meanwell 48Vdc 7.3A switching power supply. The power supply is a perfect match for the G540. Don'y be fooled into purchasing a power supply with a larger current rating. This supply will drive 4 steppers...

The G250X is one of Geckodrive's newest low-price, high-quality step motor drives.The G250X is produced using brand new techniques allowing it to  be sold for very low prices in volume while maintaining excellent quality. This is the drive...

GR214 with Horizontal Connectors The GR214 is a powerful and cost effective FPGA based step motor drive meant for high power applications. Designed from the ground up to eliminate resonance from stepper motors, the GR214 is in a class above...

GR214 with Vertical Connectors The GR214 is a powerful and cost effective FPGA based step motor drive meant for high power applications. Designed from the ground up to eliminate resonance from stepper motors, the GR214 is in a class above competing...

 The G203V Vampire is Geckodrives famous unkillable drive.         G203V Specifications:       - 7A 80VDC 10-Microstep Drive Mid-band resonance damping Short-circuit protection ...

The G251 is one of Geckodrive's newest low-price, high-quality step motor drives. This is in essence a miniaturized version of the G201 complete with a heatsink plate and 3.5mm 12 position connector.     3.5A 50VDC maximum Digitally...

  The G213V is Geckodrive's toughest drive with a step pulse multiplier, allowing it to run in full step, half step, 5 microstep and 10 microstep modes. Designed with the intention of creating an indestructible stepper controller, no...

 The G201X drive is the new G201  drive.         G201X Specifications:       - 7A 80VDC 10-Microstep Drive Mid-band resonance damping Optoisolated STEP, DIRECTION and DISABLE...

The all-new G216 Indexing Stepper Controller is the first in a new category of drives. The G216 can be sent a single pulse to start and stop motion at a user-settable speed using its onboard potentiometers, with three speed ranges to choose from....

  The G210X is the newest stepper drive from Geckodrive and is a drop-in replacement for the G210; at its core is a G201X and a G901X step pulse multiplier, allowing for full step, half step, 5 microstep and 10 microstep resolution. It is built...

    The G320X is the newest servo drive from Geckodrive, Inc. Built around the same high speed CPLD as the G203V and offering the same bulletproof protection, the G320X is a drive that will last. It was designed as a drop-in replacement...

The G901X is a step pulse multiplier that is used to convert your G201X or G203V into a G210X or a G213V, respectively. It works by synthesizing a full step, half step, 5-microstep or 10-microstep pulse based on the jumper setting; this means the...

Specs input voltage 3.6 - 5.5 Vdc current 10 mA max output voltage TTL voltage operating temperature -40 - 100°C resolution 48, 96, 100, 125, 192, 200, 250, 256, 384, 400, 500, 512, 800, 1000, 1024, 2048 PPRFeaturesThe AMT102-V Kit Utilizes...

Cable with 5-pin connector, 5 conductor shielded round 24 AWG twisted pair cable. Specifications  Connector Type 5-pin Wire Gauge 24 AWG Wire Type 5 conductor shielded round twisted pair Length 6 foot DataSheet

 This is the screw and heatsink combo for the G250. It contains a hard-anodised aluminium plate and two screws to protect your G250 from overheating and shorting out the G250 MOSFETs if they are mounted on a non-anodised piece of aluminium.

This G250 is a replacement axis drive for the REV-8 G540 Drive.  The drive does NOT have the Anti-Resonance trimpot as it in on the REV8 G540 mother board. The G250 is one of Geckodrive's newest low-price, high-quality step motor drives.The G250...

  Model No. LRS-350-48   MeanWell 48V DC 7.3A 350W  Power Supply LRS-350 series is a 350W single-output enclosed type power with 30mm of low profile design. AC input range selectable by switch Protections: Short circuit /...

  Model No. NES-450-48   MeanWell 48V DC 7.3A 450W  Power Supply AC input range selectable by switch Protections: Short circuit / Overload / Over voltage/ Over temperature Forced air cooling by built-in DC fan Built-in...

  Model No. SE-600-48 MeanWell 48V DC 12.5A 350W  Power Supply AC input active surge current limitingAC input range selectable by switchProtections: Short circuit / Overload / Over voltageForced air cooling by built-in DC fanPWM control and...

This heaksink kit is ideal for helping to keep your G540 cool when using motors that draw more than 3A. Each of the three 40mm x 40mm  heatsinks in the kit have a thermal heat-sink adhesive pad allowing for easy attachment to the G540 stepper...

A finned heatsink for easy mounting of all large Geckodrive motor controls. The products this can be used for are listed below:  G201  G201X  G202  G203V  G210  G210X  G212  G213V  G320  G320X...

 The GC-01 is a cooling fan system for the Gecko G540 4axis drive system. The GC-01 mounts to the back of the G540 by the supplies steel stand-offs, positioning the fans approximately 1/4" above the back plate of the drive. GeckoDrive...

The GC-02 DB-9 Breakout board is a great complement to the GeckoDrive four axis G540 Stepper Drive system. It provides an easy way to connect the stepper motor cables to the G540. The GC-02 BOB has a 9 pin D-Type male connector on one end and easy...

The GC-04 DB-9 I/0 Breakout board is a great complement to the GeckoDrive four axis G540 Stepper Drive system. It provides an easy way to connect to the G540 VFD and input terminals without the need for soldering. The GC-04 BOB has two 9 pin D-Type...

Replaceable fuse for the Geckodrive G540 stepper drive.

Replaceable fuse for the Geckodrive G203V stepper drive.

 This is a replacement motherboard for the latest REV-8 G540 drive

The  DB-9 stepper screw terminal Breakout board is a great complement to the Gecko Drive four axis G540 Stepper Drive system. It provides an easy way to connect the stepper motor cables to the G540 without soldering. The BOB has a 9 pin D-Type...